Home > Just for you > Decoupaged Medicine Cabinet > Page 2

Decoupaged Medicine Cabinet

Our cabinet door had holes in the middle for the hardware so we used wood putty to cover them up and sanded it flush once dry. We primed the entire door and then painted the perimeter of the front and the back with grey paint (the same colour we used for our walls.
The Frame and Shelves
Cut your top, bottom and side pieces for the frame of the box to the dimensions on your own cut list (yours will vary according to the size of your door). Our cabinet door was 29 3/4″ long by 13 1/2″ wide so we built our box (the frame) 31″ long by 14″ wide (exterior dimensions) – some of which would be covered by the face frame (which was 32″ long x 15″ wide; also exterior dimension).

decoupaged medicine cabinet

Since we don’t have too many fancy tools, we simply glued and pin nailed our box together. However, if you have carpentry skills, you can dovetail the joints. We spaced the two shelves 9″ apart, glued along the edges, clamped and then pin nailed them through the sides of the frame through the centre edge of the each shelf. You have to have a steady hand when the shelves are so thin!

decoupaged medicine cabinet

Cap off the shelves with the plastic edging by slipping it over the ends.

decoupaged medicine cabinet

I’m going to run out of picture space before I get to the best part (the decoupaged door) so head over to my blog for instructions and pictures on how to build the face frame and finish the inside of the cabinet.
 Add Some Unique Flair to the Cabinet Door
I could have left the cabinet door plain but I wanted to add a one-of-a-kind touch, so I cut up some old calendars and decoupaged four of the pictures onto the front of the door using a brush to apply the Mod Podge. I wasn’t too fussed about the cut edges because I covered them up in the last step with trim. The calendar I used for this project was one I happened to get free when I purchased my Benjamin Moore paint for the bathroom! Ever since then, I’m always on the lookout at thrift stores for new or out-of-date calendars with interesting images that can be used for decoupage, like shown below.

decoupaged medicine cabinet

To further embellish the decoupage, I pressed some leftover venetian plaster I already had on hand through an assortment of nautical and nature-inspired stencils and let it dry thoroughly. I used some fine sandpaper to knock back any rough spots on the plaster. I used a two step craquelure finish over the decoupage, tinting the second part so the original colour of the calendar would show through the cracks, as shown below. Follow the steps on the particular brand you purchase and apply both coats evenly allowing them to dry between coats. Unfortunately I didn’t take pictures of each step of the crackle process, but I’m sure I’ll do another project at some point which I’ll be sure to detail for you and I’ll link it back to here!

decoupaged medicine cabinet

Once dry, I put two coats of high gloss varnish over the decoupage/crackle finish.

decoupaged medicine cabinet

The final step is to glue on the previously painted pieces of wood trim to cover the edges of the four calendar scenes. I carefully clamped the trim pieces in place while they dried, taking care not to mar the decoupage.
Install Hinges and Mount Door
Before installing the cabinet, it’s easier to mount the hinges onto the door and face frame first so you don’t have to work vertically.

decoupaged medicine cabinet

Spread the hinges out evenly then measure and mark and door. Drill pilot holes and screw in place. Place the door evenly onto the face frame (it’s easier if you have someone to help!) then transfer the hinge holes with a pencil. Predrill the holes in the face frame and complete mounting the hinges by screwing in place. Remove the door again for the next step so the cabinet box will be lighter to maneuver.
Install the Cabinet
To mount the cabinet, we used a stud finder to find the studs. We lined our markings up with a stud on the right side of the cabinet. We marked the dimensions of the back of the cabinet on the drywall making sure our lines were level and plumb then cut a hole in our drywall. We added some additional framing for support along the left side and the bottom since the cabinet was narrower than the distance between our studs (which should be 16″ on centre).

decoupaged medicine cabinet

We mounted our box – now a full fledged cabinet – into the drywall between the studs, flush with the drywall opening.

decoupaged medicine cabinet

One thing to note: our cabinet was mounted in an interior wall. If you are placing the cabinet on an exterior wall however, just make sure that you replace and seal up any insulation removed when you cut into the wall. We drilled some pilot holes through the side frame and into the studs and used small head wood screws to fasten the box into the opening.

decoupaged medicine cabinet

Load Up Your New Medicine Cabinet
Reattach the door and it’s now ready for all your stuff to be placed on the shelves!

decoupaged medicine cabinet

Final Reveal
In the picture below you can see the final outcome of the cabinet reflected in a vintage mirror we rescued from our own basement.

decoupaged medicine cabinet

Drill a hole to add a small door pull on the outside, then and a rubber bumper on the inside of the door and you’re done!

decoupaged medicine cabinet

By making what’s essentially a box to accommodate an old door, you too can add some personality into any bathroom space with a medicine cabinet.

decoupaged medicine cabinet

If you enjoyed this post, please pin and share! For more crafty ideas, check out Birdz of a Feather ~ Craft Rehab to see projects you may have missed – and subscribe. You can also follow Birdz of a Feather on: